Monday, March 21, 2016

Cisco ME 3400 Series Switches Cabling Solution

Cisco ME 3400 Switches


Cisco is the leading provider of switches in telecommunication industry. Its switches cover a wide range of applications. One of them is deigned for Metro Ethernet application, which is widely used and known as Cisco ME 3400 series. It is a series of switches which support data rate ranging from 10 M (Mbps) to 1000 M (1 Gbps) with advantages of safety, flexibility, simple deployment and trouble shooting in network. There are several Cisco ME 3400 switch modules with different configurations to satisfy different market needs. The following table is the detailed port information of these switches.
Switch Model Port Information
Cisco ME 3400-24TS-AC 24 10/100 FastEthernet ports and 2 SFP module ports, AC power
Cisco ME 3400-24TS-DC 24 10/100 FastEthernet ports and 2 SFP module ports, DC power
Cisco ME-3400-24FS-A 24 100BASE-FX SFP module ports and 2 Gigabit Ethernet SFP module ports, AC power
Cisco ME 3400G-12CS-AC 12 dual-purpose ports and 4 SFP module ports, AC power
Cisco ME 3400G-12CS-DC 12 dual-purpose ports and 4 SFP module ports, DC power
Cisco ME 3400G-2CS 2 dual-purpose ports and 2 SFP module ports, AC power
Ports On Cisco ME 3400 Switches
Although Cisco ME 3400 has a variety of port configurations, there are mainly three types of ports on the panel rear of Cisco ME 3400 switches concluded from the above table. They are RJ45 port, SFP port and dual-purpose port. The following part will illustrate how to use these ports to connect Cisco ME 3400 switches in network.
RJ45 Port Connection
RJ45 Ports on Cisco ME 3400 Switches
It is widely known that RJ45 port are based on copper. The RJ45 Ethernet ports on Cisco 3400 switches can be connected with 10Base-T, 100Base-TX, or 1000Base-T devices via copper cables that are attached with RJ45 connector (shown in the above picture). One of the benefits of using these ports is that they can configure themselves to operate at the speed of attached devices from 10 M, 100 M to 1000 M. If the attached ports do not support auto-negotiation, the specific speed and duplex parameters can be set to the required value.
Cisco ME 3400 SFP port connection
SFP Ports on Cisco 3400 Switches
The SFP ports on Cisco ME 3400 switches are base on either fiber optic or copper. For a fiber optic connection, a fiber optic SFP module should be plugged in the SFP port firstly, then one end of fiber optic cable with fiber optic connector (usually LC connector) should be inserted into the interface of the SFP module (shown in the above picture). Then insert the other cable end into a fiber optic connector on the target device. When the status LED of the port turns green a fiber optic link is established. If the connection is based copper cable, copper SFP module and copper cable attached with RJ45 connectors should be used to link the switch and target device. Two Cisco ME 3400 switches could be connected with SFP module patch cable (as shown in the following picture).
two Cisco ME  3400 Switch connected by SFP patch cable
Dual-Purpose Ports on Cisco ME 3400 Switches
A big highlight of Cisco ME 3400 switches is its dual-purpose port. Please note that only Cisco ME 3400G-12CS-DC/AC and Cisco ME 3400G-2CS have such kind of ports. Literally, dual-purpose can be used in two different ways. One is for fiber optic connection and one is for copper connection. These ports can be can be configured as either 10/100/1000M ports or as SFP module ports according to the needs. The switch dynamically selects the media type for each dual port (10/100/1000BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP module port has priority. The following picture shows part of the Cisco ME 3400G-12CS dual-purpose ports. The Cisco ME3400G-2CS switch dual-purpose ports are similar to those shown in this section.
Cisco ME 3400 dual-purpose port information
The following picture shows both fiber optic cable and copper cables connection with Cisco ME 3400G-12CS via dual-purpose ports. For the RJ45 ports, RJ45 connector and copper cable are used. For the SFP ports, both fiber optic connection and copper connection can be achieved by using fiber optic SFP module and copper SFP module separately. Thus, Cisco ME 3400 switches armed with dual-purpose ports can greatly increase it flexibility during cabling and network designing.
dual-purpose port connection details
Cisco ME 3400 Series Switches Cabling Guide
As Cisco ME 3400 series switches could be connected to a variety types of network and devices, customer might be confused during the selecting of cables, connector and modules. The following table offers the detailed information how to connect Cisco ME 3400 switches to the network.
Port Type
Data Rate
Connectors/Modules & Cables
RJ45 Ports 10BASE-T ports  RJ-45 connectors, two-pair Cat 3, 4, or 5 unshielded twisted-pair (UTP)
100BASE-TX ports  RJ-45 connectors, two-pair Cat 5 UTP
SFP Ports 100M GLC-GE-100FX LC duplex, MMF
GLC-FE-100FX
GLC-FE-100EX LC duplex, SMF
GLC-FE-100ZX
GLC-FE-100LX
GLC-FE-100BX-D LC simplex, SMF
GLC-FE-100BX-U
1000M (1G) GLC-SX-MM LC duplex, MMF
GLC-SX-MMD
SFP-GE-S
GLC-EX-SMD LC duplex, SMF
GLC-LH-SM
GLC-ZX-SM
GLC-ZX-SMD
GLC-LH-SMD
SFP-GE-Z
SFP-GE-L
CWDM SFP
DWDM SFP
GLC-BX-U LC simplex, SMF
GLC-BX-D
RJ-45, Cat 5
GLC-T
SFP-GE-T
All the above mentioned products can be provided in Fiberstore (FS.COM). If you are interested please contact sales@fs.com or visit FS.COM for more details.

Monday, March 14, 2016

Connect Cisco Catalyst 3750 Series Switches to Network

Cisco Catalyst 3750 series switches are widely used in today’s access layer of the network, which can provide Ethernet speed of Gigabit. There are a variety of configurations in this series of Cisco switches. They can fit different applications and offering forward data rates from 32G to 128G by using Cisco StackWise technology. It is an economical solution to many midsize enterprises and office. However, to make full use of these switches, how to connect them to network becomes very important. This post will illustrate Cisco Catalyst 3750 series switches connection in details.
Do You Know Cisco Catalyst Series Switches?
The ports on switches decide what types of connectors and cables can be connected with the switches. Thus, let’s get a close look at Cisco Catalyst 3750 switches ports details first. As mentioned, one of the biggest advantages is that Cisco Catalyst 3750 can support Cisco StackWise technology. Up to nice physical Catalyst 3750 switches can be interconnected into one logical switch with a high performance of 32G or 128G. This is largely depending on the StackWise ports on the rear panel of the switch as shown in the following picture.
Cisco Catalyst 3750G-48TS rear panel
Another great advantage of Cisco Catalyst 3750 switch is its great flexibility and adaptability owning to its various configurations. The Ethernet ports of Cisco Catalyst 3750 can support data rage from 10M to 1G. For instance, or example, Cisco Catalyst 3750G-12S contains 12 SFP ports, Cisco Catalyst 3750G-24TS-1U has 24 Ethernet 10/100/1000 ports plus 4 SFP uplinks in 1 rack unit (RU) height, Cisco Catalyst 3750G-48PS is armed with 48 Ethernet 10/100/1000 ports with IEEE 802.3af PoE and 4 SFP uplinks. The following picture shows the detailed ports information of Cisco Catalyst 3750G-48TS, which has 48 Ethernet 10/100/1000 ports and 4 SFP uplinks.
Cisco Catalyst 3750G-48TS front panel
Connecting Cisco Catalyst 3750 Series Switch to Network
There are mainly two types of ports on Cisco Catalyst 3750 switches: RJ45 and SFP. Different cables and connectors are used to connect the switches to network. The following will offer detailed information about how to connect these ports.
Cisco Catalyst 3750 Switch 10/100/1000 Ports Connection
10/100/1000 Ports on Cisco Catalyst 3750 are RJ45 ports, which should be connected with copper cables (as shown in the following picture). For different applications, the cable types are also different. For example, when connecting Cisco Catalyst 3750 to workstation, servers, router, the straight-through cables are suggested to use with RJ45 connector. When it the switch is connected to repeaters, crossover cable is recommended. When connecting to 1000Base-T-compatible devices, be sure to use a twisted four-pair, Cat5 cable.
Cisco Catalyst 3750 RJ45 connection
Cisco Catalyst 3750 Switch SFP Module Ports Connection
Most Cisco Catalyst 3750 switches have several SFP ports on their front panel. They can support Gigabit Ethernet, by using SFP modules related. Both copper and fiber optic links can be built with these ports and SFP modules. If connected with fiber optic 1000Base-LX or 1000Base-SX SFP modules a link supporting Gigabit Ethernet based on fiber optic can be built. If connected with copper SFP module like 1000Base-T, a copper link will be built. The following picture illustrates the connections with fiber optic SFP module port and Copper SFP module port from left to right separately.
Cisco catalyst 3750 SFP port connection
Cabling Solution for Cisco Catalyst 3750 Series Switches
More related cables and modules that Cisco Catalyst 3750 switches supporting are listed in the following chart for your reference.
Port Type
Data Rate
Connectors/Modules & Cables
RJ45 Ports 10BASE-T ports  RJ-45 connectors, two-pair Cat 3, 4, or 5 unshielded twisted-pair (UTP)
10BASE-T PoE ports  RJ-45 connectors, two-pair Cat 3, 4, or 5 UTP cabling power pins 1, 2 (negative) and 3, 6 (positive)
100BASE-TX ports  RJ-45 connectors, two-pair Cat 5 UTP
100BASE-TX PoE ports  RJ-45 connectors, two-pair Cat 5 UTP, power on pins 1, 2 (negative) and 3, 6 (positive)
SFP Ports 100M GLC-GE-100FX LC duplex, MMF
GLC-FE-100FX
GLC-FE-100LX LC duplex, SMF
GLC-FE-100BX-D LC simplex, SMF
GLC-FE-100BX-U
1G GLC-SX-MM LC duplex, MMF
GLC-SX-MMD
SFP-GE-S
GLC-EX-SMD LC duplex, SMF
GLC-LH-SM
GLC-ZX-SM
GLC-BX-D
SFP-GE-Z
SFP-GE-L
CWDM SFP
DWDM SFP
GLC-BX-U LC simplex, SMF
GLC-T RJ-45, Cat 5
All the above mentioned products are fully tested in FS.COM Test Center. Please contact sales@fs.com for more details.

Source: http://www.fiber-optic-tutorial.com/connect-cisco-catalyst-3750-series-switches-to-network.html

Tuesday, March 8, 2016

How to Connect Cisco Nexus 9396PX to 40G Network

Both devices and network architecture should be consider during data center upgrade. With the driven of applications like Cloud, Internet of Things, and virtual data center, it is clear that 10G can no longer satisfy the application needs. Migrating to 40/100G is an urgent problem. Cisco Nexus 9396PX switch, as one of the first member of Cisco Nexus 9000 series platform, can support 40G transmission with flexibility and high density. However, the problem is that many customers do not know how to get there to make full use of these devices. This post will give a detailed description about how to connecting Cisco Nexus 9396PX switch to optimized network architecture.
spine-leaf architecture vs 3-tier architecture
Optimized Network Architecture—Spine-Leaf Architecture
The traditional network usually used a three tier network architecture. However, with the migration of 40/100G, a new architecture is taking place of the traditional one with great advantages. This is known as spine-leaf architecture. Compare with the traditional three tier network architecture, spine-leaf uses a two-tier mode as shown in the above picture. Several most obvious advantages of spine-leaf architecture are list as following:
  • spine-leaf network is more adaptable to the continuous change of data center. This is because an additional Spine switch may be added and uplinks may be extended to every Leaf switch, resulting in the addition of interlayer bandwidth and reduction of the oversubscription.
  • Spine-leaf network can create high density cabling environments depending on the scale of the network.
  • Using a two-tier mode, spine-leaf network can reduce the overall signal latency through the elimination of a switching layer.
Cisco Nexus 9396PX ports information
Connecting Cisco Nexus 9396PX to 40G Spine-Leaf Network
To make full use of the given source, spine-leaf architecture is suggested. As shown in the above picture, the Cisco Nexus 9396PX is a 2RU non-blocking Layer 2 and 3 fixed switch offering 48 ports of 1G SFP/10G SFP+ and 12 ports of 40G QSFP+. Cisco Nexus 9396PX switch is suggested to be used as the leaf switch in 40G spine-leaf network. Cisco Nexus 9396PX is suggested to be used as leaf switch in 40G spine-leaf network. In spine-leaf network architecture for 40G application, the connections between the spine switches and leaf switches are 40G, while connections between the leaf switches and servers are usually 1/10G. Thus these 40G QSFP+ ports can be used to connect the spine switch and the 1G SFP/10G SFP+ are suggested to connect servers and routers. To accomplish the whole spine-leaf connection, optics and cables or DAC (direct attach cable) should be used. The following picture shows a 40G spine-leaf architecture with Cisco Nexus 9396PX being used in the leaf layer and the fiber cabling choice for Cisco Nexus 9396PX switch in this architecture.
Cisco Nexus 9396PX spine-leaf connection solution
Cisco Nexus 9396PX Cabling Solution
Using the fixed switch Cisco Nexus 9396PX with spine-leaf architecture can greatly increase the network scaling capability and adaptability. Detailed information about modules and cables that can be used with Cisco Nexus 9396PX are listed in the following chart.
Connection Option 1: Optics & Cable Option 2: DAC
Spine to leaf (40G connection) QSFP-40G-SR4 MMF, OM3/OM4, MPO patch cable QSFP-H40G-AOC (1m to 10m are available) QSFP-H40G-CU (1m to 5m are available) QSFP-H40G-ACU (7m to 10m are available)
QSFP-40G-SR4-S
QSFP-40G-CSR4
QSFP-40GE-LR4 SMF, LC duplex patch cable
QSFP-40G-LR4
WSP-Q40GLR4L
QSFP-40G-LR4-S
QSFP-40G-ER4
Leaf to server (1/10G connection) SFP+ Optics SFP-10G-AOC (1m to 10m are available) SFP-H10GB-CU (1m to 5m are available)
SFP-10G-SR MMF, LC duplex patch cable
SFP-10G-SR-S
SFP-10G-LR SMF, LC duplex patch cable
SFP-10G-LR-S
SFP-10G-ER
SFP-10G-ER-S
SFP-10G-ZR
DWDM SFP+
SFP Optics
GLC-T (1000BASE-T) RJ-45, Cat 5
SFP-GE-T
GLC-SX-MMD MMF, LC duplex patch cable
GLC-SX-MM
GLC-LH-SMD SMF, LC duplex patch cable
GLC-EX-SMD
GLC-LH-SM
All the products mention in this chart can be customized according to your applications in Fiberstore (FS.COM). They will be fully tested in Fiberstore Test Center before they go to the market. Kindly contact sales@fs.com for more details.

Tuesday, February 23, 2016

Fanout Assemblies in 40G Interconnection

40G transmission is very common in the backbone network now. However, not all the devices and network are upgraded to 40G. To adapting the network between devices and network of different data rate. It is necessary to connection 40G devices to 10G devices for network interconnection. To solve this problem, fanout technology is be accepted and widely used in data center. Fanout products for interconnection is easy to understand. It’s kind of like the water pipeline in our building: water is transferred from the trunk pipeline in a building. Then trunk pipeline fans out into several pipelines that have smaller diameters to bring the water to every house. This post will introduce several Fanout products that are commonly used for 40G data center interconnection.
40G MPO Fanout Cables
The first fanout component is 40G MPO fanout cable, also called breakout cable or harness cable. MPO fanout cable is a multi-fiber optical cable with one end terminated with a male/female MPO connector and the other end attached with several LC connectors. Actually, there are various types of MPO fanout cables, according to connector type, cable length and cable type. But they all have the similar structure. Here will introduce three most popular MPO fanout cables according to the package type.
MPO-8LC fanout cable
The first one to be introduced is also what most customer need. This cable is fan out into 12 fibers or 24 fibers. The above picture shows a typical 12-fiber MPO harness cable. The MPO connector of this fanout cable is linked to 6 duplex LC connectors, which is really useful for backbone cabling from 40G devices to 10G devices. The second one is a little bit smaller version of the former. The fibers are fanout directly from the MPO connectors. With small size, this kind of mini MPO harness cable can be easily put into patch panel and increase the cabling density largely and effectively.
12-fiber MPO cassette
The third to be introduced is a special one—MPO cassette. Literally, it looks like a cassette and looks very different from other MPO fanout cables. However, when you look inside the cassette, it has not much difference from other MPO fanout cables. MPO Cassette actually contains one or several mini MPO fanout cables in side the cassette, which is designed for those who want have everything in clean and tidy status. As it can be installed in a standard rack and the cables are all well protected. A 12-fiber MPO cassette usually has a 12-fiber mini MPO fanout cable in side the cassette, with a MPO connector on the backside and 12 LC connector in the front. For a 24-fiber MPO cassette, there could be a 24-fiber fanout cable or two 12-fiber cables inside. The following picture is a MPO cassette with two 12-fiber MPO fanout cable inside it, thus there are two MPO connector on its backside.
24-fiber MPO cassette with two 12-fiber MPO fanout inside
40G Fanout Direct Attach Cables
To decrease the 40G interconnection cost, Direct attach cable (DAC) is being widely used. There are also fanout versions of 40G DAC which support 40G to 10G cabling. These kind of 40G DAC usually have one QSFP+ connector on one end and four SFP+/XFP connectors or several LC connectors at the other end. For example, the following is 40G QSFP+ to 8 LC DAC. The QSFP+ connector of it can be used to plug in the 40G device which has QSFP+ port. On the other end, the four duplex LC connectors are used to separately connect four SFP+ transceivers , which are used to plug in 10G devices with SFP+ switched (shown in the following picture). If you used a 40G QSFP+ to 4 SFP+ DAC, this process would be easier, cause the SFP+ connector can be plugged into the SFP+ switch directly.
QSFP-8LC AOC for 40G to 10G cabling
Conclusion
All in all, fanout technology plays an important role in the 40G data center for both connecting devices supporting different data rate and distribution. Most fanout products are factory pre-terminated. The installation and maintenance doesn’t need many skills. In Fiberstore, a variety of fanout products of high quality and reliability can be customized according to your application. If you are seeking for solutions for fanout product, please feel free to contact sales@fs.com for more details.

Wednesday, February 17, 2016

Cabling With High Density Push-Pull Tab Patch Cords

It is inevitable to plug fiber patch cables from the patch panels, switches or cassettes in today’s data center cabling. However, this simple movement becomes harder and harder nowadays. Why? Both the data rate of every optical fiber and the fiber counts being used are increased to support high data rate up to 40/100G or more. Thus, the cabling density increased largely with the deployment of 40/100G Ethernet network. Finger access to every patch cable that is loaded on the patch panel, switches or cassettes becomes difficult. Especially for these patch cables in the middle of the space.
For fiber patch cords attached with connectors like LC, things become more complex. Because this type of connectors are usually locked in the port with a latch on the connector body. If you want to plug out a patch cord with LC connectors, you should firstly unlock the connector from the port by clicking the latch with is with small size (shown in the following picture). Usually an external tool is used to unplug the specific connector in a high density cabling. It seems a problem doesn’t matter much in the whole cabling. However, during practical cabling, network engineer could be headache about this annoying problem. To find an easy and elegant way to solve this finger access problem, a new type of patch cords was invented, which is designed for high density cabling and is known as push-pull tab patch cords.
finger access for high-density cabling
What Is High Density Push-pull Tab Fiber Patch cable?
Compare with the traditional patch cords. This new type patch cord is attached with a connector with a push-pull tab, which can perfectly solve the fiber access problem in high density cabling. Except the additional tab for pushing and pull, these connectors don’t change much from the traditional ones that attached to patch cords. But this little change makes a great difference. The following is offering you the details about this novel product.
High density push-pull tab fiber patch cords are usually attached with LC or MPO connectors, as these two types of connector are currently the most popular in high density cabling like 40G, 100G, 120G or more. The following pictures shows the details of these two types of connectors with push-pull tab.
The one in the left of the following picture is an LC connector attached on push-pull tab patch cable. It’s of standard LC size. When the tab is pulled the LC connector would be unlocked from the port easily, cause the tab is linked to the latch of the LC connector. Once the LC connector is unlocked, the patch cords would be smoothly plugged out from the port and other patch cords around it by pulling the tab slightly. As for MPO connector with push-pull tab shown in the following picture on the right side. Finger access becomes easier. The tab can greatly simplify the use of MPO connectivity when manual access to the release slider and rear portion of the connector is restricted. In this way, easy insertion and extraction of MPO patch cords can be achieved.
push-pull tab patch cords connectors
Get More From Push-pull Tab Patch Cable
Is finger access the only advantage of push-pull tab patch cords. Definitely NO. The following illustrating will surely make you exciting about push-pull tab patch cable.
  • Flexibility and adjustability: it has been proved that push-pull tab can increase the cabling density by 30% to 50%, which can satisfy the future high density cabling requirements for 120G or more.
  • Reliability: To reach the specific connector you want, you might loosen or remove other connectors around it, which can highly increase the reliability of the network.
  • Cost-save and time-save: it is clear that with push-pull tab patch cords, cabling becomes easy and elegant with higher ROI.
Fiberstore Push-Pull Tab Fiber Patch Cable Solutions
If you are looking for a simple and easy high density patch cabling solution, push-pull tab patch cords provided by Fiberstore can satisfy your requirements. The following chart is the most common applications of push-pull tab patch cords for your references.
Application Patch Cords Cable Type Connectors on Both Ends
10G to 10G Cabling Duplex LC Push-pull Tab Patch Cord OM3/OM4/Single-mode Duplex LC Duplex LC
40G to 40G Cabling 12-fiber MPO Push-pull Tab Trunk Cable OM3/OM4/Single-mode MPO (male/female) MPO (male/female)
40G to 10G Cabling 12-fiber MPO to 8 LC Push-pull Tab Break out Cable OM3/OM4/Single-mode MPO (male/female) 4 Duplex LC
100G to 100G Cabling 24-fiber MPO Push-pull Tab Trunk Cable OM3/OM4/Single-mode MPO (male/female) MPO (male/female)
For more details and customized solution of push-pull tab patch cords, you can always access Fiberstore by FS.COM or emailing us at sales@fs.com

Saturday, January 16, 2016

Understanding Loss in Fiber Optic

Fiber optic transmission has various advantages over other transmission methods like copper or radio transmission. Fiber optic which is lighter, smaller and more flexible than copper can transmit signals with faster speed over longer distance. However, many factors can influence the performance of fiber optic. To ensure the nice and stable performance of the fiber optic, many issues are to be considered. Fiber optic loss is a negligible issue among them, and it has been a top priority for many engineers to consider during selecting and handling fiber optic. This article will offer detailed information of fiber optic loss.
light-in-fiber-optic
When a beam of light which carrying signals travels through the core of fiber optic, the strength of the light will become lower. Thus, the signal strength becomes weaker. This loss of light power is generally called fiber optic loss or attenuation. This decrease in power level is described in dB. During the transmission, something be happened and causes the fiber optic loss. To transmit optical signals smoothly and safely, fiber optic loss must be decreased. The cause of fiber optic loss located on two aspects: internal reasons and external causes of fiber optic, which are also known as intrinsic fiber core attenuation and extrinsic fiber attenuation.
Intrinsic Fiber Core Attenuation
Internal reasons of fiber optic loss caused by the fiber optic itself, which is also usually called intrinsic attenuation. There are two main causes of intrinsic attenuation. One is light absorption and the other one is scattering.
Light absorption is a major cause of fiber optic loss during optical transmission. The light is absorbed in the fiber by the materials of fiber optic. Thus light absorption is also known as material absorption. Actually the light power is absorbed and transferred into other forms of energy like heat, due to molecular resonance and wavelength impurities. Atomic structure is in any pure material and they absorb selective wavelengths of radiation. It is impossible to manufacture materials that are total pure. Thus, fiber optic manufacturers choose to dope germanium and other materials with pure silica to optimize the fiber optic core performance.
Scattering is another major cause for fiber optic loss. It refers to the scattering of light caused by molecular level irregularities in the glass structure. When the scattering happens, the light energy is scattered in all direction. Some of them is keeping traveling in the forward direction. And the light not scattered in the forward direction will be lost in the fiber optic link as shown in the following picture. Thus, to reduce fiber optic loss caused by scattering, the imperfections of the fiber optic core should be removed, and the fiber optic coating and extrusion should be carefully controlled.
Extrinsic Fiber Attenuation
scattering in fiber optic
Intrinsic fiber core attenuation including light absorption and scattering is just one aspect of the cause in fiber optic loss. Extrinsic fiber attenuation is also very important, which are usually caused by improper handling of fiber optic. There are two main types of extrinsic fiber attenuation: bend loss and splicing loss.
macro bend VS. micro bend
Bend loss is the common problems that can cause fiber optic loss generated by improper fiber optic handling. Literally, it is caused by fiber optic bend. There are two basic types. One is micro bending, and the other one is macro bending (shown in the above picture). Macro bending refers to a large bend in the fiber (with more than a 2 mm radius). To reduce fiber optic loss, the following causes of bend loss should be noted:
  • Fiber core deviate from the axis;
  • Defects of manufacturing;
  • Mechanical constraints during the fiber laying process;
  • Environmental variations like the change of temperature, humidity or pressure.
fiber optic splicing is another main causes of extrinsic fiber attenuation. It is inevitable to connect one fiber optic to another in fiber optic network. The fiber optic loss caused by splicing cannot be avoided, but it can be reduced to minimum with proper handling. Using fiber optic connectors of high quality and fusion splicing can help to reduce the fiber optic loss effectively.
loss in fiber optic
The above picture shows the main causes of loss in fiber optic, which come in different types. To reduce the intrinsic fiber core attenuation, selecting the proper fiber optic and optical components is necessary. To decrease extrinsic fiber attenuation to minimum, the proper handling and skills should be applied.

Thursday, December 17, 2015

Basic of Optical Distribution Frame (ODF)

ODFDriven by requirements for high-speed data rate, the deployment of fiber optic has been growing. As the growth of installed fiber optic, the management of optical transmission networks becomes more difficult. Many factors should be considered during fiber optic cabling, like flexibility, future viability, cost of the deployment and management, etc. To handle large amounts of fiber optic with lower cost and higher flexibility, various optical distribution frames (ODF) are being widely used to connector and schedule optical fiber. Choosing right fiber optic distribution frames is the key to successful cable management.
What Is ODF?
An optical distribution frame (ODF) is a frame used to provide cable interconnections between communication facilities, which can integrate fiber splicing, fiber termination, fiber optic adapters & connectors and cable connections together in a single unit. It can also work as a protective device to protect fiber optic connections from damage. The basic functions of ODFs provided by today's vendors are almost the same. However, they come into different shapes and specifications. To choose the right ODF is not an easy thing.
Types of ODF
According to the structure, ODFs can mainly be divided into three types, namely wall mount ODF, floor mount ODF and rack mount ODF.
Wall mount ODF (shown in the following picture) usually uses design like a small box which can be installed on the wall and is suitable for fiber distribution with small counts. Floor mount ODF adopts closed structure. It is usually designed with relatively fixed fiber capacity and nice appearance.
wall mount ODF
Rack mount ODF (shown in the following picture) is usually modularity in design with firm structure. It can be installed on the rack with more flexibility according to the fiber optic cable counts and specifications. This kind of optical distribution system is more convenient and can provide more possibilities to the future variations. Most of the rack mount ODF is 19'', which ensures that they can be perfectly installed on to the commonly used standard transmission rack.
rack-mount-ODF
ODF Selection Guide
The selection of the ODF is not limited to the structure, many factors like applications should be considered. Some of the most important are introduced as following.
Fiber Counts: with the number of fiber connections in places like data center increase, the need for high density ODF become the trend. And it is very common to find ODF with 24 ports, 48 ports or even 144 ports for fiber optic cables in the market now. Meanwhile, many vendors can provide the customized ODFs according to the customers' requirement.
Manageability: High-density is the good but management is not easy. ODF should provide an easy management environment for technicians. The basic requirement is ODF should allow for easy access to the connectors on the front and rear of those ports for insertion and removal. This requires that ODF should reserve enough space. In addition, the color of adapters installed on the ODF should be remain consistent with the color code of fiber optic connectors to avoid wrong connections.
Flexibility: as mentioned rack mount ODF is relatively flexible during applications with the modular design. However, anther aspect which can increase the ODF’s flexibility effectively is the port size for adapters on the ODF. For example, an ODF with ports of duplex LC adapter size can be installed with duplex LC, SC or MRTJ adapters. An ODF with ports of ST adapter size can be installed with both ST adapters and FC adapters.
Protection: optical distribution frames integrate fiber connections in it. The fiber connections like splicing joint, fiber optic connectors are actually really sensitive in the whole transmission network and is directly related to the stability and reliability of the network. Thus, a good ODF should have protection device to prevent fiber optic connections from damages produced by dust or stress.
Conclusion
The ODF is the most popular and comprehensive fiber optic distribution frame which can reduce the cost and increase the reliability and flexibility of fiber optic network during both deployment and maintenance. The high density ODF is the trend in telecommunication industry. Selecting an ODF is important and complex which requires full consideration including applications and management. The factors like structure, fiber counts and protection are just the basic elements. The ODF which can meet the current requirements and the challenge of future growing and easing of expansion without sacrificing cable management or density can only be selected with repeated comparison and full consideration.